- 您现在的位置：买卖IC网 > Sheet目录313 > AT45DB321C-TC (Atmel)IC FLASH 32MBIT 40MHZ 28TSOP
AT45DB321C
If a Group A mode is in progress (not fully completed), then another mode in Group A should not
be started. However, during this time in which a Group A mode is in progress, modes in Group B
can be started, except the first two Group A commands (Memory Array Read Commands).
This gives the DataFlash the ability to virtually accommodate a continuous data stream. While
data is being programmed into main memory from buffer 1, data can be loaded into buffer 2 (or
vice versa). See application note AN-4 (“Using Atmel’s Serial DataFlash”) for more details.
7.4
7.4.1
7.4.2
7.4.3
7.4.4
7.4.5
Pin Descriptions
Serial Input (SI)
The SI pin is an input-only pin and is used to shift data serially into the device. The SI pin is used
for all data input, including opcodes and address sequences.
Serial Output (SO)
The SO pin is an output-only pin and is used to shift data serially out from the device.
Serial Clock (SCK)
The SCK pin is an input-only pin and is used to control the flow of data to and from the
DataFlash. Data is always clocked into the device on the rising edge of SCK and clocked out of
the device on the falling edge of SCK.
Chip Select (CS)
The DataFlash is selected when the CS pin is low. When the device is not selected, data will not
be accepted on the input pin (SI), and the output pin (SO) will remain in a high impedance state.
A high-to-low transition on the CS pin is required to start an operation, and a low-to-high transi-
tion on the CS pin is required to end an operation or to start an internally self-timed operation.
Write Protect (WP)
The WP pin is used to control the Hardware Sector Protection. Hardware Sector Protection is
enabled by asserting the WP pin and keeping the pin in it’s asserted state. Disabling Hardware
Sector Protection is accomplished by simply deasserting the WP pin. The WP pin will override
the software controlled sector protection method but only for protecting the sectors. For exam-
ple, if the sectors were not previously protected by the Enable Sector Protection command, then
simply asserting the WP pin for the minimum specified time (t WPE ) would enable the sector pro-
tection. When the WP pin is deasserted; however, the sector protection would no longer be
enabled as long as the Enable Sector Protection command was not issued while the WP pin was
asserted. If the Enable Sector Protection command was issued before or while the WP pin was
asserted, then simply deasserting the WP pin would not disable the sector protection. In this
case, the Disable Sector Protection command would need to be issued while the WP pin is
deasserted to disable the sector protection. The Disable Sector Protection command is also
ignored whenever the WP pin is asserted.
To ensure backwards compatibility with previous generations of DataFlash, the function of the
WP pin has not changed. Therefore, when the WP pin is asserted, certain sectors in the memory
array will be protected, and when the WP pin is deasserted, the memory array will be unpro-
tected provided the Enable Sector Protection command hasn’t been issued. New devices are
shipped from Atmel with the contents of the Sector Protection Register pre-programmed with
“00H” (unprotect). The user can reprogram the Sector Protection Register to change which sec-
tors will be protected by the WP pin.
15
3387M–DFLASH–2/08
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AT45DB642-TC
IC FLASH 64MBIT 20MHZ 40TSOP
AT88CK9000-8TH
CRYPTO PROGRAMMER BOARD 8-TSSOP
AT88SC12816C-MJ
IC EEPROM 128KBIT 1.5MHZ M2J
AT88SC25616C-MJ
IC EEPROM 256BIT 1.5MHZ M2J
AT88SC3216C-MJ
IC EEPROM 32KBIT 1.5MHZ M2J
AT88SC6416C-MJ
IC EEPROM 64KBIT 1.5MHZ M2J
AT91EB40A
KIT EVAL FOR ARM AT91R40008
AT91EB42
KIT EVAL FOR ARM AT91M42800A
相关代理商/技术参数
AT45DB321C-TI
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-megabit 2.7 volt DataFlash
AT45DB321C-TU
功能描述:IC FLASH 32MBIT 40MHZ 28TSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:RAM 存储器类型:SDRAM 存储容量:256M（8Mx32） 速度:143MHz 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:90-VFBGA 供应商设备封装:90-VFBGA（8x13） 包装:托盘 其它名称:Q2841869
AT45DB321D
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:2.7V 32Mbit dataflash
AT45DB321D_07
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-megabit 2.7-volt DataFlash
AT45DB321D_08
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-megabit 2.7-volt DataFlash
AT45DB321D_09
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-megabit 2.7-volt DataFlash
AT45DB321D_12
制造商:AD 制造商全称:Analog Devices 功能描述:32Mb, 2.5V or 2.7V DataFlash
AT45DB321D-CCU
功能描述:闪存 32M 2.7-3.6V, 66Mhz Serial 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel